回转风机日常维护及保养事项：

Routine maintenance and care of rotary fan:

1.润滑系统的检查回转风机严禁缺油运转

1. Inspection of lubrication system: the rotary fan shall not run without oil

1、检查油箱内的润滑油是否低于zui低油位，如储油量不足请加油建议用68#液压油，低温寒冷地区可适当降低机油牌号。

1. Check whether the lubricating oil in the oil tank is lower than Zui low oil level. If the oil storage is insufficient, please add oil. It is recommended to use 68 # hydraulic oil. In low-temperature and cold areas, the oil grade can be appropriately reduced.

2、检查机油是否混入水份等污物而变质，如变质请及时更换机油。

2. Check whether the engine oil is deteriorated due to water and other dirt. If it is deteriorated, please replace the engine oil in time.

3、清洗油过滤器，如太脏请及时更换。

3. Clean the oil filter. If it is too dirty, please replace it in time.

4、检查滴油嘴的滴油状况是否正常，如滴油嘴脏了可卸下调整螺钉清洗。

4. Check whether the oil dripping condition of the oil drip nozzle is normal. If the oil drip nozzle is dirty, remove the adjusting screw for cleaning.

2、保持风机房环境卫生，周边无油污或杂质，保持良好通风很关键。

2. It is very important to keep the environment of the fan room clean and free of oil stain or impurities, and maintain good ventilation.

3、空气滤清器的检查，如脏了可卸下空气滤清器，旋开蝶型螺母，拿开盖子，清洗过滤海绵如太脏请及时更换卸滤清器时注意不要把脏物掉进风机主机内。

3. Check the air filter. If it is dirty, remove the air filter, unscrew the butterfly nut, remove the cover, and clean the filter sponge. If it is too dirty, please replace it in time. When removing the filter, be careful not to drop dirt into the fan main body.

4、检查风机有无漏油、漏气的部位，如有这种情况，请及时维修，或及时联系生产厂家来进行专业维修。

4. Check whether there is oil or air leakage in the fan. If so, please repair it in time or contact the manufacturer for professional maintenance.

5、皮带的检查，风机运行一段时间后，皮带会松弛会伸长或破损，如松弛要将电机的固定螺栓松开，移动电机，拉紧三角带到合适位置后再将电机固定螺栓紧住，并注意电机皮带轮和风机皮带轮的端面要在同一平面上，同时检查一下两皮带轮的顶紧螺丝是否松掉，如松了请紧住。

5. Inspection of the belt: after the fan runs for a period of time, the belt will be loose, elongated or damaged. If it is loose, loosen the fixing bolts of the motor, move the motor, tighten the V-belt to a proper position, and then tighten the fixing bolts of the motor. Note that the end faces of the motor pulley and the fan pulley should be on the same plane. At the same time, check whether the top screws of the two pulleys are loose. If they are loose, please tighten them.

6、经常检查安全阀的灵活状况，如不灵活请清洗调试以保证可靠的启闭。

6. Frequently check the flexibility of the safety valve. If it is not flexible, please clean and debug it to ensure reliable opening and closing.

7、检查风机及电机的运行状况，如发现异常震动或噪音、温度不正常时要及时停机检修，找出故障原因及相应处理方法。

7. Check the operation condition of the fan and motor. In case of abnormal vibration, noise and temperature, stop the machine for maintenance in time to find out the cause of the fault and the corresponding treatment methods.

回转风机主要用途：一、各种工业污水或废水处理鼓风曝气 二、医院或实验室、生活污水的污水搅拌曝气 三、印刷行业的真空送纸 四、塑焊、吹风的气源供应 六、燃烧器的喷雾、玻璃工业 七、 需要气源的其他设备

Main uses of rotary fan: 1. Blowing and aeration for various industrial sewage or wastewater treatment; 2. Sewage mixing and aeration for hospitals or laboratories and domestic sewage; 3. Vacuum paper feeding for printing industry; 4. Air supply for plastic welding and blowing; 6. Spray for burners and glass industry; 7. Other equipment requiring air supply

以上就是为大家介绍的有关甘肃回转风机厂家的详细的介绍,希望对您有所帮助.如果您有什么疑问的话,欢迎联系我们.我们将以专业的态度,为您提供服http://www.sdyqtc.com

The above is the detailed introduction of Gansu rotary fan manufacturers. I hope it will help you. If you have any questions, please contact us. We will provide services for you with a professional attitude http://www.sdyqtc.com

相关文章： 陕西离心式风机厂家 净化器 气力输送设备厂家 油烟 甘肃回转风机厂家